ADSS Fiber Optic Cable--en

ADSS Fiber Optic Cable

ADSS Fiber Optic Cable installation span more than 1000 meters, It could be installed on the same tower for high voltage power line, or used for telecom system lines spanning rivers and mountains.

ADSS is an alternative to OPGW and OPAC with lower installation cost. The cables are designed to be strong enough to allow lengths of up to 700 metres to be installed between support towers. ADSS cable is designed to be lightweight and small in diameter to reduce the load on tower structures due to cable weight, wind, and ice.

In the design of the cable, the internal glass optical fibers are supported with little or no strain, to maintain low optical loss throughout the life of the cable. The cable is jacketed to prevent moisture from degrading the fibers. The jacket also protects the polymer strength elements from the effect of solar ultraviolet light.

Using single-mode fibers and light wavelengths of either 1310 or 1550 nanometres, circuits up to 100 km long are possible without repeaters. A single cable can carry as many as 864 fibers.

1.Product Introduction of the ADSS Fiber Optic Cable
With high tensile strength, installation span reaches more than 1000 meters to the maximum. Free from metallic material, with good insulation performance. Special outer sheath with strong resistance against electric corrosion.It could be laid on the same tower for high voltage line of 200KV or higher. Aramid yarn reinforcement with strong resistance against shock and bullet. With light weight Convenient for installation and maintenace (unnecessary for power supply stop)
2.  Application Range of the ADSS Fiber Optic Cable: It could be installed on the same tower for high voltage power line, or used for telecom system lines spanning rivers and mountains.
3.  Mounting Ways of the ADSS Fiber Optic Cable:  for aerial mounting
4.  Application Temperature of the ADSS Fiber Optic Cable: -40 ~ +70℃Remarks: W- ideal value for cable used under worst wether condition(covering ice, wind, extreme temperature, etc.) considering actualcircumstances (drop, span,height difference, etc.); T- ideal value forcable used under common weather conditions (common covering ice,wind, extreme temperature, etc.) considering actual circumstances(drop, span, height difference,etc.)W,T value could be confirmed through discussion with customers.Application Temperature: 40 ~+70;Attenuation coefficient change at 1310nm and 1550nm remains no more than 0.05dB/km within the range.Electric & Environmental Performance Water Penetration Performance: water block for whole crosssection(tested in L-shaped water rough)

Span (m)	Min. Breaking Force (kN)	Max. Operation Tension (kN)	Cable Module 104N/mm2)	Nominal Cable Outer Diameter(mm)	Cable Weight(kg/m)
100	14.1	6.6	0.4	14	0.17
200	22.3	10.5	0.6
300	28.2	13.2	0.8
400	44.7	17.6	1.2	15	0.19
500	50.2	19.8	1.4
600	55.9	22	1.5
700	61.4	24.2	1.7
800	67	26.4	2.1	16	0.22
900	72.6	28.6	2.2
Weather Conditions for Reference		10m/s wind 5mm ice 25m/s wind 0mm ice
Item	Test Conditions	Indices	Additional Attenuation	Optic Fiber Strain
Tension(N)	Short-term	W	<0.05dB	<1.5%
	Long-term	T	<0.02dB	<0.05%
Crush(N)	Short-term	>4000	<0.05dB
	Long-term	>2000	<0.02dB
Temperatuer Cycle	~40~+65℃	2cycles	<0.10dB
Vibration Resistance	Low frequency, small amplictude	>one hundred million times	<0.10dB
Water Penetration	1m cable, 1m water depth, 24h, full cross section	No
Electric Corrosion Resistance	More than 100 times spray of 3000S NaCL solution plus 0.1% activator under 4Kv	No
Allowed Bending Radius	For installation	20 times of cable diameter
	For operation	10 times of cable diameter
Allowed Side Pressure (N/100mm)	Short-term	>4000
	Long-term	>2000